I inetrface LM35 with arduino leonardo....intially the correct value was sensed by LM35 then the IC pre heated and temperature value increase gradually.what can i do ,please any one help me..

Views: 334

Replies to This Discussion

Hi,

I attached the datasheet because I am not sure if you have it.  Read it over if you haven't already.

It is probably measuring the temperature correctly so you have to figure out what could be making the temperature go up.  It could be where it is placed.  I cannot give advice without having a lot more information about what you are doing with it and how you hooked it up.

Start with the datasheet and then lets go from there...

Attachments:

i use the detail given in the following attached file...the temperature value not stable..and also IC heated..what is the reason? any other interface circuit method available

Attachments:

It's good that you are using a proven circuit configuration.  This helps narrow down the possibilities.  It would be helpful if you stated the temperature readings you are getting over time.  Example, at power on, one second later, two seconds later, etc.  Also, if the IC is getting too hot to touch it, there is definitely something wrong and you should immediately disconnect the power. 

Here is a partial list of possibilities from most likely to least likely:

1) Something is connected incorrectly.  Do you have a multimeter?  It is best to check the connections with a multi-meter on the ohms setting.  If you don't know how, find a YouTube tutorial.  If you are an expert, you can probably find the mistake visually.

2) Any possibility the power input voltage is incorrect?  Double check it with the multi-meter on the DC volts setting. (Again, YouTube if you don't know how).

3) Incorrect component value populated.  It is easy to mis-read the component value.  Example, 10 ohms or 100 ohms instead of 10K ohms.

4-100: A bunch of reasons I forgot about.

101) Faulty component.  Extremely unlikely unless you actually burned it out in the process of monkeying around.  The way to check it is to isolate each component one at a time and measure them with a meter.  E.g., measure your potentiometer in each setting (lowest and highest), hook up the temp sensor in a basic circuit without the Arduino.  If it works on its own, it will work in the circuit.  If it still doesn't, there is something else wrong.

The reason I put Faulty Component as # 101 is in my experience it is the least likely problem with a new circuit.  Usually the problem is caused by something to do with the wiring.

Have you used a breadboard before?  If not, don't assume you know how it works.  Use some small wires and a meter to figure out where the internal breadboard connections go.  You could be assuming something about the breadboard that is wrong.

thank u sir.i will check and tell the result.

RSS

Latest Activity

iftekhar Mobin is now a member of GarageLab (arduino, electronics, robotics, hacking)
21 hours ago
Profile IconLeicester Hibbert and Michael Young joined GarageLab (arduino, electronics, robotics, hacking)
Jan 9
Profile IconThorsten Schwarz and Dana Custer joined GarageLab (arduino, electronics, robotics, hacking)
Jan 2
Aqeel munir updated their profile
Dec 31, 2016
Todd Enger updated their profile
Dec 29, 2016
FRANK KWABENA is now a member of GarageLab (arduino, electronics, robotics, hacking)
Dec 28, 2016
Ayhan Chaplan commented on GarageLab's blog post How to use a Peltier with Arduino
"Hi! Will this setup work with a 3,8V / 2,5A Peltier element? Or do I have to reduce the resistance…"
Dec 26, 2016
Profile IconAyhan Chaplan, Erva and Donna Carter joined GarageLab (arduino, electronics, robotics, hacking)
Dec 26, 2016
Galy Huang posted a discussion

Ubuntu on Firefly-RK3399

Firefly-RK3399 with dual-core Cortex-A72 and quad-core Cortex-A53, ARM® Mali-T860 MP4 quad-core…See More
Dec 20, 2016
Chase Rangel posted a discussion

What is the simplest way to control one brushless motor forward/reverse?

  Hello everyone I don't know much about this type of stuff had only a handful of RC cars.I've been…See More
Dec 12, 2016
Profile IconErving Howe, Chase Rangel, Werner Pretorius and 1 more joined GarageLab (arduino, electronics, robotics, hacking)
Dec 12, 2016
Frank Turner is now a member of GarageLab (arduino, electronics, robotics, hacking)
Dec 9, 2016
Marcelo Rodrigues and swapnil are now friends
Dec 6, 2016
Marcelo Rodrigues replied to swapnil's discussion Tiny 85 based Thermometer
"Dear Swapnil, Since you don't have any experience with programming you should consider start…"
Dec 5, 2016
swapnil posted a discussion

Tiny 85 based Thermometer

Hi, can any one guide me how to make the tiny 85 based Thermometer which will glow the LED…See More
Dec 4, 2016
Spyros Svoronos is now a member of GarageLab (arduino, electronics, robotics, hacking)
Dec 4, 2016
K Biju is now a member of GarageLab (arduino, electronics, robotics, hacking)
Nov 29, 2016
Profile Iconswapnil and Yasser joined GarageLab (arduino, electronics, robotics, hacking)
Nov 28, 2016
udit is now a member of GarageLab (arduino, electronics, robotics, hacking)
Nov 25, 2016
Aqeel munir is now a member of GarageLab (arduino, electronics, robotics, hacking)
Nov 23, 2016

© 2017   Created by Marcelo Rodrigues.   Powered by

Badges  |  Report an Issue  |  Terms of Service