Arduino robotic hand under $200
Robotic hand is one of most important parts in robot equipment. This is main manipulator that…See More
#42
arduino leonardo
how to interface lcd with arduino leonardo?i follow the data and program given in the arduino software many times but no output come..please help anyone to me...
Replies to This Discussion
-
Permalink Reply by Kathy Moseler on -
First the basics, check what kind of LCD display they expect in the SW and make sure yours is compatible. If it is compatible, then verify it has power.
-
-
Permalink Reply by Jonathan Dean on -
Does your screen do anything at all? Flash? Light up? Lines? Blocks? The Arduino LiquidCrystal library is for LCDs based on the Hitachi HD44780 chipset, but they have libraries for many other common chipsets on the LCD Playground page. If your LCD lights up or displays garbage you probably have a different chipset. More information about your device and what it's doing would be helpful to get more help!
-
-
Permalink Reply by selvakumar on
-
ya in my LCD BACKGROUND LIGHTS ON and simply black colour blocks come.i use 16*2 JHD 162A .this LCD is compatible with HD44780 ?
-
-
Permalink Reply by Kathy Moseler on
-
Hi, I think this thread might help you. I didn't read it, but it sounds like a similar problem.
-
-
Permalink Reply by Jonathan Dean on
-
If you get lights and blocks then the LCD is working and not getting any data. It looks like the JHD uses the HD44780 chipset, so it should work with the LiquidCrystal library. I'd check your wiring, or redo it from scratch. Make sure all of your grounds are grounded, and make sure your contrast pot is hooked up correctly (5V on one pin, ground on the other, and the middle pin goes to the LCD). Make sure that the R/W pin is grounded. Make sure that in your code you initialize the LiquidCrystal library with the correct pins (if you look at the LiquidCrystal constructor, you'll use the first option with rs, enable, and d4, d5, d6, and d7); tell the library which pin on the Arduino is connected to each of the LCD pins. After that, be sure you call LCD.begin(16, 2). Also, for my LCD sometimes I have to reset the Arduino once or twice to get it to work.
-
Latest Activity
abhishek yadav posted a discussionhow to record time between two events using arduion
i have a disk rotating at variable speed(max rpm 600) . i want to know how much time it takes to…See More
Danny Vigo commented on Fernando Gil's blog post Tutorial: Servomotor + Arduino"Why would you want to connect them in parallel? Are you trying to increase the current? Perhaps to…"
Danny Vigo replied to SATYA NARAYANA REDDY NIMMAKAYALA's discussion 5 stepper motor control code"Well if you look in the examples that come included with the Arduino IDE you can find some code…"
Christian Rheinnecker posted a status"New Video Cypress Hill - Rap Superstar
https://www.youtube.com/watch?v=VZSFgdrhzQQ"
Christian Rheinnecker posted a videoArduino PrX : Sequencer AM808 VX3 - Demo Cypress Hill - Rap Superstar Beat Play
Demonstration eines Beats auf dem AM808 VX3 Arduino Midi Sequencer Cypress Hill - Rap Superstar Weiter Infos auf http://arduinoprx.de
"Im not sure why people turn to IC's for sound or power. I had this little amp kicking around…"
Mark Harrison commented on Thulana Vimukthi's blog post GPS GUIDED AUTONOMOUS ROBOT"Thulana, very excellent project!
It is especially nice, as the hardware connections are relatively…"
GarageLab posted a blog postMake your Thor's Hammer
Rather than being a benign foam hammer, this Mjölnir can summon 80,000 volts of electricity thanks…See More
© 2013 Created by Marcelo Rodrigues.
