i just bought a arduino leonardo,i just tried to run hello word sketch on it but i was not able to see any thing on the lcd. all connection was done properly .

pin used on arduino- 12,11,5,4,3,2

lcd- winstar

pls help if anyone has any idea.

Views: 1950

Reply to This

Replies to This Discussion

i am also have the same trouble...

Have you got your contrast pot hooked up?  If it's hooked up correctly, you should see an effect when you turn it even if nothing is displayed.  If that's working, try resetting the Arduino a time or two.  If it still doesn't work, I'd suggest redoing rather than just checking your wiring.  Make sure you hook up all the grounds, and make sure they have a good connection. Also, it wouldn't hurt to post a picture, schematic, or listing of your pin connections (for example, are you sure pin 11 on the Arduino is hooked to the enable pin on your LCD?).

i tried what u suggest but i did not work , so i uploaded the image. if u find any mistake in wiring pls make me know.

 

Well, it looks like all of the pins go to the right places.  Does the screen light up when you power it on?  Do you see one line blacked out and the other not?  What happens when you sweep the pot from one extreme to the other?  Sometimes on my breadboard I have to wiggle the wires some to get a good connection, especially the grounds.

only the back light LED glow.there is no other change in display when i sweep the port.

I just tried my LCD to see what happens.  If the LCD and backlight are powered, the contrast pot doesn't do anything and the display is just blank (exactly what yours is doing).  I suppose that means that the Arduino isn't communicating with it properly.  Can you post your setup code?  Maybe try wiring it to different pins just to see what happens (it could be that, say, the ENABLE and RS are swapped).  Are the pins marked on the LCD board?

Please consider this:
http://www.johngineer.com/blog/?p=1224

[quote]For example, the lower 8 digital pins are no longer all a single port, and many of the pins, with the exception of the RX and TX lines, are moved around. Some of the PWM lines are in the same place, but are now connected to different ports and OC registers than they were before.[/quote]

which means many of the libraries will probably have to be rewritten.

RSS

Latest Activity

Profile IconMarvin Wright and chaudhari vipin vasudev joined GarageLab (arduino, electronics, robotics, hacking)
yesterday
Marcelo Rodrigues replied to Peter Davies's discussion Anyone got stock of Garagelabs automation board
"Peter, I will talk them to check if they can produce more units and make available on their…"
Tuesday
Brian B. Feaster commented on GarageLab's blog post Information Trade Between Cars by Wi-Fi
"I like this idea of information trade between cars by the WI-Fi . This would contribute in reducing…"
Tuesday
Peter Davies replied to Peter Davies's discussion Anyone got stock of Garagelabs automation board
"Hi Marcello I have bought all of Seeeds stock in two purchases - 8 units in all.  When I asked…"
Tuesday
Profile Icontarun patel, Enrique S. Perez Rodriguez, K Fiore and 5 more joined GarageLab (arduino, electronics, robotics, hacking)
Monday
Marcelo Rodrigues replied to Peter Davies's discussion Anyone got stock of Garagelabs automation board
"Peter, You can buy them on…"
Monday
Rob Lambert joined Marcelo Rodrigues's group
Thumbnail

Arduino

Group for the Arduino communitySee More
Saturday
Sardar Tamoor commented on Thulana Vimukthi's blog post GPS GUIDED AUTONOMOUS ROBOT
"can you plz help me on my project !!! its basically obstacle avoidance in dynamic environment and…"
Apr 27
Sardar Tamoor commented on Thulana Vimukthi's blog post GPS GUIDED AUTONOMOUS ROBOT
"can you plz help me on my project !!! its basically obstacle avoidance in dynamic environment and…"
Apr 27
Sardar Tamoor is now a member of GarageLab (arduino, electronics, robotics, hacking)
Apr 26
Peter Davies posted a discussion

Anyone got stock of Garagelabs automation board

HiI have a requirement for 11 automation boards and have been able to source 8,  does anyone have a…See More
Apr 25
Profile IconGuilherme Barros, Rob Lambert and kevin parr joined GarageLab (arduino, electronics, robotics, hacking)
Apr 22
Tino Pascuzzi left a comment for stephen smith
"Hello, my name is Tino Pascuzzi and I'm the owner of The Sanctuary Haunted Attraction.  I…"
Apr 14
Tino Pascuzzi left a comment for Aaron Thiedt
"Hello, my name is Tino Pascuzzi and I'm the owner of The Sanctuary Haunted Attraction.  I…"
Apr 14
Tino Pascuzzi left a comment for Paul Ellison
"Hello, my name is Tino Pascuzzi and I'm the owner of The Sanctuary Haunted Attraction.  I…"
Apr 14
Tino Pascuzzi left a comment for Gary
"Hello, my name is Tino Pascuzzi and I'm the owner of The Sanctuary Haunted Attraction.  I…"
Apr 14
Tino Pascuzzi left a comment for Amauri
"Hello, my name is Tino Pascuzzi and I'm the owner of The Sanctuary Haunted Attraction.  I…"
Apr 14
Mark Mendelsihn is now a member of GarageLab (arduino, electronics, robotics, hacking)
Apr 14
Tino Pascuzzi updated their profile
Apr 13
ade ljathanna is now a member of GarageLab (arduino, electronics, robotics, hacking)
Apr 12

© 2016   Created by Marcelo Rodrigues.   Powered by

Badges  |  Report an Issue  |  Terms of Service